52551. What is the input impedance of a common-gate configured JFET?
52552. JFET terminal "legs" are connections to the drain, the gate, and the:
52553. A very simple bias for a D-MOSFET is called:
52554. With the E-MOSFET, when gate input voltage is zero, drain current is:
52555. With a 30-volt VDD, and an 8-kilohm drain resistor, what is the E-MOSFET Q point voltage, with ID = 3 mA?
52556. When an input signal reduces the channel size, the process is called:
52557. Which JFET configuration would connect a high-resistance signal source to a low-resistance load?
52558. How will electrons flow through a p-channel JFET?
52559. When VGS = 0 V, a JFET is:
52560. When applied input voltage varies the resistance of a channel, the result is called:
52561. When is a vertical channel E-MOSFET used?
52562. When the JFET is no longer able to control the current, this point is called the:
52563. With a JFET, a ratio of output current change against an input voltage change is called:
52564. Which type of JFET bias requires a negative supply voltage?
52565. How will a D-MOSFET input impedance change with signal frequency?
52566. The type of bias most often used with E-MOSFET circuits is:
52567. The transconductance curve of a JFET is a graph of:
52568. The common-source JFET amplifier has:
52569. Using voltage-divider biasing, what is the voltage at the gate VGS?
52570. The overall input capacitance of a dual-gate D-MOSFET is lower because the devices are usually connected:
52571. What is the transconductance of an FET when ID = 1 mA and VGS = 1 V?
52572. Which component is considered to be an "OFF" device?
52573. In an n-channel JFET, what will happen at the pinch-off voltage?
52574. Breakdown voltage and pinch-off voltage of a JFET are different terms for the same voltage level.
52575. A JFET can be either a current-controlled device or a voltage-controlled device.
52576. A JFET has 3 terminals: gate, drain, and source.
52577. An enhancement-type MOSFET or E-MOSFET can be turned on when the channel is depleted.
52578. The charge carriers in a junction field effect transistor (JFET) will flow from source to drain in a p-channel and from drain to source in an n-channel.
52579. In a voltage-divider JFET circuit, ID is a maximum when VGS = 0 V.
52580. The amount of gate voltage needed to turn the JFET completely off is called VGS(OFF).
52581. A common-drain configured JFET is also called a source-follower.
52582. If the drain, source, and channel are all a p-type material, and the transistor operates in both modes, this is a p-channel E-MOSFET.
52583. A D-MOSFET cannot be biased using zero biasing.
52584. The main sea port of Pandyas?
52585. Transconductance is also called mutual conductance.
52586. A JFET is very similar to a BJT.
52587. A MOSFET has an isolated gate.
52588. The gate-biased JFET characteristic curve includes IDS.
52589. To get a negative gate-source voltage in a self-biased JFET circuit, you must use a ________.
52590. One advantage of voltage-divider bias is that the dependency of drain current, ID, on the range of Q points is _________.
52591. A royal Muslim family of Kerala?
52592. A __________ change in VDS will produce a __________ change in ID.
52593. A _______________ JFET amplifier provides a voltage gain of less than one.
52594. Junction Field Effect Transistors (JFET) contain how many diodes?
52595. When an input delta of 2 V produces a transconductance of 1.5 mS, what is the drain current delta?
52596. When not in use, MOSFET pins are kept at the same potential through the use of:
52597. D-MOSFETs are sometimes used in series to construct a cascode high-frequency amplifier to overcome the loss of:
52598. A "U" shaped, opposite-polarity material built near a JFET-channel center is called the:
52599. Which is the best example of Regneration?
52600. If both inputs of an S-R NAND latch are LOW, what will happen to the output?