The store house of dried; pressed and preserved plant specimens is known as? ?->(Show Answer!)

1. The store house of dried; pressed and preserved plant specimens is known as?

Answer: Herbarium

Reply

Comments

Tags

Show Similar Question And Answers

QA->The store house of dried; pressed and preserved plant specimens is known as?....

QA->A building where works of art, scientific specimens and other objects of permanent value are kept and displayed.....

QA->Cloves are dried flower buds of which plant?....

QA->Amendment by special majority means the bill is passed in each house by a majority of the total membership and by a majority not less than ........ of the members that house present and voting?....

QA->A man takes 4 hours in all to go to a market at a speed of 5km/hour and back to his house at 3km/hour. The distance between his house and market is:....

MCQ->Two products are sold from a vending machine, which has two push buttons P1 and P2. When a button is pressed, the price of the corresponding product is displayed in a 7-segment display. If no buttons are pressed, '0' is displayed, signifying 'Rs' .0'. If only P1 is pressed, '2' is displayed, signifying 'Rs. 2'. If only P2 is pressed, '5' is displayed, signifying 'Rs. 5'. If both P1 and P2 are pressed, 'E' is displayed, signifying 'Error'. The names of the segments in the 7-segment display, and the glow of the display for '0', '2', '5' and 'E', are shown below. Consider push button pressed/not pressed is equivalent to logic 1/ 0 respectivelya segment a to g are considered as functions of P1 and P2, then which of the respectively. If segments a to g are considered as functions of P1 and P2, then which of the following is correct?...

MCQ->Four friends A, B, C and D live in a same locality. The house of B is in the east of A's house but in the north of C's house. The house of C is in the west of D's house. D's house is in which direction of A's house?...

MCQ->The simplest method of welding two pieces of metal together is known as pressure welding.The ends of a metal are heated to a white heat-for iron,the welding temperature should be about 1300C-in a flame.At this temperature the metal becomes plastic.The ends are pressed or hammered together,and the joint is smoothed off.Care must be taken to ensure that surfaces are thoroughly clean first,for dirt will weaken the weld.Moreover,the heating of iron or steel to a high temperature cause oxidation,and a film of oxide is added to the heated surfaces.For this reason,flux is applied to the heated metal.At welding heat,flux melts and the oxide particles are dissolved in it together with any other impurities which may be present.The metal surfaces are pressed together,and the flux is squeezed out from the center of the weld.A number of different types of weld may be used,but for fairly thick bars of metals,a vee-shaped belt should be normally employed.It is rather stronger than ordinary butt weld. The simplest way of welding two pieces of metal together is...

MCQ->Which of the following are not privileges enjoyed by members of Parliament individually? I. Freedom from being arrested in civil cases during and 40 days before and after the continuance of a meeting of the House of Committee of which he is a member. II. Freedom from being summoned without the leave of the House, to give evidence as a witness while Parliament is in session. III. Unlimited freedom of speech providing immunity from court action for anything said in the House. IV. Freedom to publish debates and proceedings of the House.?...

MCQ->Refer to the keyboard encoder in figure (a). Sometimes when the 5 key is pressed, the system attached to the keypad does not respond. The 5 input on the 74147 is monitored with a digital storage scope while repeatedly pressing the 5 key, and the waveform in figure (b) is obtained; the P above the trace indicates the points at which the technician pressed the key. What is most likely wrong with the circuit?

Terms And Service:We do not guarantee the accuracy of available data ..We Provide Information On Public Data.. Please consult an expert before using this data for commercial or personal use | Powered By:Omega Web Solutions
© 2002-2017 Omega Education PVT LTD...Privacy | Terms And Conditions Question ANSWER With Solution