1. You install the Routing and Remote Access service on a Windows 2000 Server computer in your network. Your network is not directly connected to the Internet and uses the private IP address range 192.168.0.0. When you use Routing and Remote Access to dial in to the server, your computer connects successfully, but you are unable to access any resources. When you try to piiig servers by using their IP addresses, you receive the following message: "Request timed out." When you run the ipconfig command, it shows that your dial-up connection has been given the IP address 169.254.75.182. What should you do to resolve the problem?






Ask Your Doubts Here

Type in
(Press Ctrl+g to toggle between English and the chosen language)

Comments

Show Similar Question And Answers
QA->A _____ is a computer attached to the internet that runs a special web server software and can send web pages out to the other computer over the internet.....
QA->In order to promote growth and investment, a new provision has been inserted in the Income-tax Act with effect from FY 2019-20 which allows any domestic company an option to pay income-tax at the rate of __ per cent subject to condition that they will not avail any exemption/incentive.?....
QA->“Try not to become a man of success but rather to become a man of value”?....
QA->Who proclaimed It is years since I left castes and religions. Yet some people think that I belong to their caste. That is not correct. I do not belong to any particular caste or religion?....
QA->The citizens in distress can dial which number to get immediate access to emergency services?....
MCQ->You install the Routing and Remote Access service on a Windows 2000 Server computer in your network. Your network is not directly connected to the Internet and uses the private IP address range 192.168.0.0. When you use Routing and Remote Access to dial in to the server, your computer connects successfully, but you are unable to access any resources. When you try to piiig servers by using their IP addresses, you receive the following message: "Request timed out." When you run the ipconfig command, it shows that your dial-up connection has been given the IP address 169.254.75.182. What should you do to resolve the problem?....
MCQ->The Corporate router receives an IP packet with a source IP address of 192.168.214.20 and a destination address of 192.168.22.3. Looking at the output from the Corporate router, what will the router do with this packet? Corp#sh ip route [output cut] R 192.168.215.0 [120/2] via 192.168.20.2, 00:00:23, Serial0/0 R 192.168.115.0 [120/1] via 192.168.20.2, 00:00:23, Serial0/0 R 192.168.30.0 [120/1] via 192.168.20.2, 00:00:23, Serial0/0 C 192.168.20.0 is directly connected, Serial0/0 C 192.168.214.0 is directly connected, FastEthernet0/0....
MCQ->You have the following routing table. Which of the following networks will not be placed in the neighbor routing table? R 192.168.30.0/24 [120/1] via 192.168.40.1, 00:00:12, Serial0 C 192.168.40.0/24 is directly connected, Serial0 172.16.0.0/24 is subnetted, 1 subnets C 172.16.30.0 is directly connected, Loopback0 R 192.168.20.0/24 [120/1] via 192.168.40.1, 00:00:12, Serial0 R 10.0.0.0/8 [120/15] via 192.168.40.1, 00:00:07, Serial0 C 192.168.50.0/24 is directly connected, Ethernet0....
MCQ->Your network contains NetWare 4.0 Servers. You have successfully installed Client Service for NetWare on Windows 2000 Professional computers, and Gateway Service for NetWare on Windows 2000 Server Computers. You recently added a new Windows 2000 Server computer to the network and installed Gateway Service for NetWare on it. However, the server is unable to connect to any NetWare servers. What should you do on the new Windows 2000 Server computer to resolve this problem?....
MCQ->Your network contains 10 domain controllers, 10 member servers, and approximately 1,000 client computers. All the servers run Windows 2000 Server, and all the client computers run Windows 2000 Professional. Two of the domain controllers act as DNS servers. Users of client computers use file sharing to grant access to files stored locally. The network has 10 subnets and uses TCP/IP as the only network protocol. You want to configure the network so that all computers can resolve the addresses of all other computers by using DNS. Client computers must be able to register and resolve addresses if a server fails. How should you configure the DNS servers?....
Terms And Service:We do not guarantee the accuracy of available data ..We Provide Information On Public Data.. Please consult an expert before using this data for commercial or personal use | Powered By:Omega Web Solutions
© 2002-2017 Omega Education PVT LTD...Privacy | Terms And Conditions