1. Referring to the figure given below, what output code will appear on the output (A3,A2,A1,A0) when the 5 key is pressed?





Ask Your Doubts Here

Type in
(Press Ctrl+g to toggle between English and the chosen language)

Comments

Show Similar Question And Answers
QA->A statement followed by two assumptions I and II is given. You have to consider the statement to be true even if it seems to be at variance from commonly known facts. You are to decide which of the given assumptions can definitely be drawn from the given statement. Indicate which one of the four given alternatives is correct ? Statement : If more encouragement is given to Sports, Indians will win more gold medals at the Olympic Games. Assumptions : I. Indians do not win gold medals. II. More enc....
QA->In a secret way of writing COME AT ONCE FATHER VERY ILL is written as XLNV ZG LMXY UYGSVI EVIB ROO.Bearing this in mind pick up the code from the answer choices for the word given below: FIT AND WELL....
QA->കീബോർഡിലെ Escape Key (Esc Key) എവിടെയാണ് കാണാൻ സാധിക്കുക? ....
QA->Which is the Master Key of the Key Board?....
QA->Two statements are given followed by two conclusions I and II. You have to consider the two statements to be true even if they seem to be at variance from commonly known facts. You have to decide which one of the given conclusions is definitely drawn from the given statements. Statement : All virtuous persons are happy. No unhappy person is virtuous. Conclusions : I. Happiness is related to virtue II. Unhappy person is not virtuous.....
MCQ->Two products are sold from a vending machine, which has two push buttons P1 and P2. When a button is pressed, the price of the corresponding product is displayed in a 7-segment display. If no buttons are pressed, '0' is displayed, signifying 'Rs' .0'. If only P1 is pressed, '2' is displayed, signifying 'Rs. 2'. If only P2 is pressed, '5' is displayed, signifying 'Rs. 5'. If both P1 and P2 are pressed, 'E' is displayed, signifying 'Error'. The names of the segments in the 7-segment display, and the glow of the display for '0', '2', '5' and 'E', are shown below. Consider push button pressed/not pressed is equivalent to logic 1/ 0 respectivelya segment a to g are considered as functions of P1 and P2, then which of the respectively. If segments a to g are considered as functions of P1 and P2, then which of the following is correct?....
MCQ->Referring to the figure given below, what output code will appear on the output (A3,A2,A1,A0) when the 5 key is pressed?

....
MCQ->Refer to the keyboard encoder in figure (a). Sometimes when the 5 key is pressed, the system attached to the keypad does not respond. The 5 input on the 74147 is monitored with a digital storage scope while repeatedly pressing the 5 key, and the waveform in figure (b) is obtained; the P above the trace indicates the points at which the technician pressed the key. What is most likely wrong with the circuit?

....
MCQ->Consider the following statements about Infix and Post fix notations in Pascal In Infix notation operators appear between the operands on which they operate.In Post fix notation operators appear after the operand.The Infix expression A + B - C + D will appear as AB + C - D + in post fix notation. Which of the above are correct?....
MCQ->The simplest method of welding two pieces of metal together is known as pressure welding.The ends of a metal are heated to a white heat-for iron,the welding temperature should be about 1300C-in a flame.At this temperature the metal becomes plastic.The ends are pressed or hammered together,and the joint is smoothed off.Care must be taken to ensure that surfaces are thoroughly clean first,for dirt will weaken the weld.Moreover,the heating of iron or steel to a high temperature cause oxidation,and a film of oxide is added to the heated surfaces.For this reason,flux is applied to the heated metal.At welding heat,flux melts and the oxide particles are dissolved in it together with any other impurities which may be present.The metal surfaces are pressed together,and the flux is squeezed out from the center of the weld.A number of different types of weld may be used,but for fairly thick bars of metals,a vee-shaped belt should be normally employed.It is rather stronger than ordinary butt weld. The simplest way of welding two pieces of metal together is....
Terms And Service:We do not guarantee the accuracy of available data ..We Provide Information On Public Data.. Please consult an expert before using this data for commercial or personal use | Powered By:Omega Web Solutions
© 2002-2017 Omega Education PVT LTD...Privacy | Terms And Conditions
Question ANSWER With Solution