Question Set

1. Using the illustration from the previous question, what would be the IP address of S0 if you were using the first subnet? The network ID is 192.168.10.0/28 and you need to use the last available IP address in the range. Again, the zero subnet should not be considered valid for this question.





Ask Your Doubts Here

Type in
(Press Ctrl+g to toggle between English and the chosen language)

Comments

  • By: guest on 02 Jun 2017 01.57 am
    A /28 is a 255.255.255.240 mask. The first subnet is 16 (remember that the question stated not to use subnet zero) and the next subnet is 32, so our broadcast address is 31. This makes our host range 17-30. 30 is the last valid host.
Show Similar Question And Answers
QA->Correct sentences among the following are: ) The tea is too hot that I cannot drink (2) Work hard, lest you should miss the chance (3) Unless you study well, you will fail (4) Unless you study well, you will pass....
QA->P and Q need 8 days to complete a work. Q and R need 12 days to complete the same work. But P, Q and R together can finish it in 6 days. How man D. 4 days will be needed if P and R together do it?....
QA->A cyclist goes 40 km towards East and then turning to right he goes 40 km. Again he turn to his left and goes 20 kn. After this he turns to his left and goes 40 km, then again turns right and goes 10 km. I-low far is he from his starting point ?....
QA->If you have a Power point show you created and want to send using E-mail to another teacher you can add the show to your E-mail message as an______....
QA->Dr Ambedkar had said that Article ___ should normally remain a 'dead letter' and would be used only in the 'last resort'.?....
MCQ->The Corporate router receives an IP packet with a source IP address of 192.168.214.20 and a destination address of 192.168.22.3. Looking at the output from the Corporate router, what will the router do with this packet? Corp#sh ip route [output cut] R 192.168.215.0 [120/2] via 192.168.20.2, 00:00:23, Serial0/0 R 192.168.115.0 [120/1] via 192.168.20.2, 00:00:23, Serial0/0 R 192.168.30.0 [120/1] via 192.168.20.2, 00:00:23, Serial0/0 C 192.168.20.0 is directly connected, Serial0/0 C 192.168.214.0 is directly connected, FastEthernet0/0....
MCQ->You have the following routing table. Which of the following networks will not be placed in the neighbor routing table? R 192.168.30.0/24 [120/1] via 192.168.40.1, 00:00:12, Serial0 C 192.168.40.0/24 is directly connected, Serial0 172.16.0.0/24 is subnetted, 1 subnets C 172.16.30.0 is directly connected, Loopback0 R 192.168.20.0/24 [120/1] via 192.168.40.1, 00:00:12, Serial0 R 10.0.0.0/8 [120/15] via 192.168.40.1, 00:00:07, Serial0 C 192.168.50.0/24 is directly connected, Ethernet0....
MCQ->Using the illustration from the previous question, what would be the IP address of S0 if you were using the first subnet? The network ID is 192.168.10.0/28 and you need to use the last available IP address in the range. Again, the zero subnet should not be considered valid for this question.....
MCQ->Using the following illustration, what would be the IP address of E0 if you were using the eighth subnet? The network ID is 192.168.10.0/28 and you need to use the last available IP address in the range. The zero subnet should not be considered valid for this question. ....
MCQ->You are working with three networks that have the network IDs 192.168.5.0, 192.168.6.0, and 192.168.7.0. What subnet mask can you use to combine these addresses into one?....
Terms And Service:We do not guarantee the accuracy of available data ..We Provide Information On Public Data.. Please consult an expert before using this data for commercial or personal use | Powered By:Omega Web Solutions
© 2002-2017 Omega Education PVT LTD...Privacy | Terms And Conditions
Question ANSWER With Solution