53702. The polarity on the side of the resistor where current enters is ______. The polarity on the side of the resistor where current exits is ___________.

53703. A voltage divider is always a _____

53704. If five equal resistors are connected in series with a 20 V source, and a current of 400 µA is measured, each resistor equals ___.

53705. If four 90 resistors are connected in series across an 18 V source, the current equals ___.

53706. –1.2 V, +15 V, and –6 V batteries are connected in series. The magnitude of total voltage is _________.

53707. In the given circuit, _____ are in series.

53708. What is the current flow through R1, R2, and R3?

53709. One of the most common applications of a potentiometer is as an adjustable voltage divider, also known as

53710. If the resistance total in a series circuit doubles, current will:

53711. The Governor can nominate to the Ligislature Council of his state one member from this community:

53712. What is the dc source voltage?

53713. When a Wheatstone bridge is in a balanced condition, the center voltmeter in the bridge will read:

53714. When a load is connected to a voltage divider, the total resistance of the circuit will:

53715. With 21 V applied, if R1 = 5 ohms, R2 = 35 ohms, and R3 = 14 ohms, what is the current of R2 if R1 is series connected with parallel circuit R2 and R3?

53716. What is the total resistance of a circuit when R1 (7 k ) is in series with a parallel combination of R2 (20 k ), R3 (36 k ), and R4 (45 k )?

53717. If the load in the given circuit is 80 k , what is the bleeder current?

53718. What is the total resistance of the given circuit?

53719. What are the branch currents I2 and I3?

53720. If the load in the given circuit is open, what is the unloaded output voltage?

53721. Right to Information Act(RTI)became effective in India on 15th June:

53722. How much voltage is dropped across R3 in the given circuit?

53723. When placed into a circuit, how are electronic components usually connected?

53724. If the load in the given circuit is 12 k , what is the loaded output voltage?

53725. If a Wheatstone bridge is balanced, a voltmeter in the center of the bridge will read:

53726. What is the voltage to the load?

53727. The first goal to accomplish in analyzing a complex series-parallel circuit is to

53728. Which circuit fault do the meter readings in the given figure indicate?

53729. How much current is flowing through R1 in the given circuit?

53730. If R1 is in series with parallel connected to R2 and R3, what happens to total current if R2 opens?

53731. The first goal(s) to accomplish in analyzing a complex series–parallel circuit is to:

53732. If a series–parallel circuit has all 30-ohm resistors, what is the total resistance when R1 is in series with a parallel circuit consisting of R2 and R3?

53733. Components or combinations of components with common currents, in a series–parallel circuit, are in:

53734. What determines if resistor connections are in series, parallel, or series–parallel?

53735. Universal Declaration of human rights was passed by the UN General Assembly on:

53736. If R1 is in series with a parallel combination of R2, R3, and R4, when the resistance value of R2 increases, the voltage across R3 will

53737. A Wheatstone bridge can be used to determine an unknown

53738. The proclamation of emergency brings automatic suspension of the right to:

53739. In a series–parallel circuit consisting of R1 and R2 in series and connected in parallel with R3, if R1 opens, then R2's voltage will:

53740. In the given circuit, what is RUNK equal to if RV must be adjusted to 1,232 in order to balance the bridge?

53741. With 6 V applied, what is the voltage across R2 of a parallel combination of R2 (1 k ), R3 (2 k ), and R4 (1 k ) in series with R1, whose value is 2 k ?

53742. What is the power dissipated by R1, R2, and R3?

53743. In the given circuit, the Thevenin voltage equals 6 V.

53744. The voltage across R3 is 20 volts.

53745. The voltage across R1 is 175 volts.

53746. In the given circuit, the Thevenin resistance equals 800 .

53747. The voltmeter will read 18 volts.

53748. Bleeder current is the total current left after the total divider current is subtracted from the total current into the circuit.

53749. When analyzing series–parallel circuit currents, you should start with the current in the branch farthest from the source.