<<= Back Next =>>
You Are On Multi Choice Question Bank SET 1075

53751. The total resistance in the circuit is 1.6 k.



53752. The current through R1 is 17 mA.



53753. If the output voltage of a certain loaded voltage divider is 12 V, the output voltage might decrease when the load is removed.



53754. If the Wheatstone bridge is balanced in the given circuit, the voltage between points A and B (VAB) equals the source voltage (VS).



53755. The current through R6 is 8.5 mA.



53756. Observed voltages not being shared identify components in parallel in a series–parallel circuit.



53757. R2 is open.



53758. The total power is 10 watts.



53759. The total resistance in the given circuit can be found using the formula: RT = R1 + R2 || R3 || R4.



53760. When a load resistance is connected to the output of a voltage divider circuit, the source current increases.



53761. Opens and shorts are typical problems that occur in electric circuits.



53762. A Wheatstone bridge may be used to determine the value of an unknown resistance.



53763. The voltage out when a 10 k load is connected is 5.7 volts.



53764. When resistors burn out, they usually short.



53765. Attaching a 6 k load to a voltage divider will cause a smaller decrease in the output voltage than will attaching a 5 k load.



53766. A loaded voltage divider is a common application of a series-parallel circuit.



53767. The loading effect of a voltmeter can be ignored if ____.





53768. A Thevenin equivalent circuit contains _____.





53769. In the given circuit, the current flowing through R3 equals ______.





53770. Series components in a series–parallel circuit may be in series with other _______________ components, or with other _______________ components.





53771. If four 10 k resistors are in series with a single 20 k resistor and one of the parallel resistors shorts, the voltage across the other parallel resistors ________.





53772. In the given circuit, the voltage dropped across R1 equals _____.





53773. ___ is often used to analyze multiple-source circuits.


53774. If R3 opens in the given circuit, the total resistance (RT) between points A and B equals ____.





53775. If a Wheatstone bridge is balanced, its output voltage is ____.





53776. When a load is connected to a voltage divider, the total resistance of the circuit will ________.





53777. In the given circuit, the total resistance (RT) between points A and B equals _____.





53778. In the given circuit, the voltage at point A equals ______.





53779. If the voltage between points A and B equals 9 V in the given circuit, then VR3 equals ______.





53780. What theorem replaces a complex network with an equivalent circuit containing a source voltage and a series resistance?





53781. What is the power dissipated by R2, R4, and R6?





53782. If the load in the given circuit is 120 k , what is the loaded output voltage?





53783. In a series–parallel circuit, individual component power dissipations are calculated using:





53784. The current flowing through an unloaded voltage divider is called the:





53785. The primary function of the oscillator in an isolation amplifier is to





53786. Refer to Figure 20-2. This circuit is a setup for





53787. An instrumentation amplifier has a high





53788. This circuit is a setup for





53789. Circuits that shift the dc level of a signal are called





53790. A byte can hold one.......of data?





53791. In the classic three-op-amp instrumentation amplifier, the differential voltage gain is usually produced by the





53792. Typical isolation amplifiers use optical coupling.



53793. The concept of Fundamental right has it’s basis in the:





53794. The chairman of the UPSC is appointed by the:





53795. Kerala is the first state in India to launch a Pension Scheme for farmers namely:





53796. According to 2001 census,the state having highest urban population is:





53797. Isolation amps are named as such because they are sealed for protection from outside environmental damage.



53798. The district in Kerala which has got the highest density of population as per 2001 census:





53799. Clampers are often called peak detectors.



53800. The Union Territory in India with the highest population:





<<= Back Next =>>
Terms And Service:We do not guarantee the accuracy of available data ..We Provide Information On Public Data.. Please consult an expert before using this data for commercial or personal use | Powered By:Omega Web Solutions
© 2002-2017 Omega Education PVT LTD...Privacy | Terms And Conditions
Question ANSWER With Solution