29151. When two plates butt together and are riveted with two cover plates with two rows of rivets, the joint is known as
29152. The moment diagram for a cantilever which is subjected to a uniformly distributed load will be a
29153. The areas of cross-section of a square beam and a circular beam subjected to equal bending moments, are same.
29154. For the same height, the bottom width for no tension,
29155. Maximum deflection of a
29156. Which is the border line that sepaerates India and Pakistan?
29157. For a beam, if fundamental equations of statics are not sufficient to determine all the reactive forces at the supports, the structure is said to be
29158. The moment diagram for a cantilever carrying linearly varying load from zero at its free end and to maximum at the fixed end will be a
29159. The maximum deflection of
29160. Which is the Mecca of Kerala Football?
29161. The intensity of direct longitudinal stress in the cross-section at any point distant r from the neutral axis, is proportional to
29162. A rectangular bar of width b and height h is being used as a cantilever. The loading is in a plane parallel to the side b. The section modulus is
29163. Which gas is used to extinguish fire?
29164. The ratio of strengths of solid to hollow shafts, both having outside diameter D and hollow having inside diameter D/2, in torsion, is
29165. The weakest section of a diamond riveting, is the section which passes through
29166. In a loaded beam, the point of con-traflexture occurs at a section where
29167. മലയാളവും സംസ്കൃതവും ഇടകലർന്ന ഭാഷയേത്? [Malayaalavum samskruthavum idakalarnna bhaashayeth?]
29168. Where is the headquarters of National Thermal Power Corporation situated?
29169. What is the sum of the even integers from 100 to 1000?
29172. For design of a column the eccentricity of loading shall be taken as the distance from the assumed point of application of the load to the centroid of the column, subject to a minimum of
29173. Rewrite as directed: 'To beat the air' approximately means (Meaning of the phrase in italics)?
29174. India’s first fast breeder neutron reactor is?
29175. The Industrial Revolution gave rise to .........?
29176. The concrete is deemed not to comply with the strength requirements if the strength is less than the greater of
29177. The maximum area of compression reinforcement in a beam of cross section B x D is limited to
29178. Moist curing of the exposed surfaces of concrete is done at least for
29179. If 100/3 cr 3n-3n-1=891,then the value of ‘n’is:
29180. If the ratio of effective span to overall depth of a simply supported beam is equal or greater than 1 but less than or equal to 2, the lever arm, is
29181. If the slenderness ratio of a column is more than 160, the compressive stress obtained by the secant formula is multiplied by a factor in which value of x is
29182. For battened struts, the effective length is increased by
29183. Shankaracharya did not establish ‘Math’ in?
29184. The test strength of the sample is taken as the average of the strength of
29185. The maximum deflection of a structure should not normally exceed lesser of the span/350 or
29186. Pick up the correct statement regarding columns.
29187. For heavily reinforced concrete member, the nominal maximum size of the aggregates should be restricted to
29188. The minimum pitch i.e., the distance between centres of rivet holes is not less than
29189. Dispersion of load through the flange to web is considered as dispersed uniformly at an angle θ° is
29190. The grade of concrete generally not used in the reinforced concrete, is
29191. The outstand of stiffeners should be (where t is the thickness of flat).
29192. For the plain reinforcing bars in compression, the permissible design bond stress in tension, is increased by
29193. The cover to the main reinforced may be reduced up to one third of the specified cover but not less than
29194. The maximum compressive strength on 15 cm cubes of M 20 grade concrete at 7 days, should be a minimum of
29195. The reduced level of third floor of a building near a column is 205.350 m. The reduced levels of the undersides of four beams supporting the fourth floor framing into the column mutually perpendicular are 208.350 m, 208.450 m, 208.500 m and 208.550 m. The supported length of the column is
29196. The distance between, rivet line and the nearest edge of a joint not exposed to weather, is taken (where t is thickness in mm of the thinner outside plate).
29197. Pick up the correct precaution while spilicing the reinforcing bars
29198. Who was the world’s first women elected Prime Minister?
29199. The over all depth of a solid slab is 20 cm and effective depth is 15 cm. The horizontal distance between parallel main reinforcement should not be more than
29200. The ratio of minimum compressive strength on 15 cm cubes prepared with the concrete of M 20 grade and M 40 grade, at 7 days should be at least