Question Set

1. The radiation heat flux from a heating element at a temperature of 800°C, in a furnace maintained at 300°C is 8 kW/m2. The flux, when the element temperature is increased to 1000°C for the same furnace temperature is





Ask Your Doubts Here

Type in
(Press Ctrl+g to toggle between English and the chosen language)

Comments

Show Similar Question And Answers
QA->Rs.800 becomes Rs.956 in 3 years at certain rate of simple interest.If the rate of interest is increased by 3%,What amount will Rs.800 becomes in 3 years?....
QA->If the temperature of a hot body is increased by 50% the amount of radiation emitted by it increases approximately by?....
QA->Which alloy used in making heating elements for electric heating devices?....
QA->കൃഷ്ണൻ അവന്റെ വീട്ടിൽനിന്നും ആദ്യം 500 മീറ്റർ വടക്കോട്ട് നടന്നു. പിന്നീട് വലത്തോട്ട് തിരിഞ്ഞ് 800 മീറ്ററും ഇടത്തോട്ട് തിരിഞ്ഞ് 800 മീറ്ററും നടന്നു. എ ങ്കിൽ പുറപ്പെട്ട സ്ഥലത്തുനിന്നും നേരെ അയാളി ലേക്കുള്ള ദൂരം എത്ര? ....
QA->Which colour of heat radiation represents the highest temperature?....
MCQ->The radiation heat flux from a heating element at a temperature of 800°C, in a furnace maintained at 300°C is 8 kW/m2. The flux, when the element temperature is increased to 1000°C for the same furnace temperature is....
MCQ->The atmospheric air at dry bulb temperature of 15°C enters a heating coil maintained at 40°C. The air leaves the heating coil at 25°C. The by-pass factor of the heating coil is....
MCQ->The simplest method of welding two pieces of metal together is known as pressure welding.The ends of a metal are heated to a white heat-for iron,the welding temperature should be about 1300C-in a flame.At this temperature the metal becomes plastic.The ends are pressed or hammered together,and the joint is smoothed off.Care must be taken to ensure that surfaces are thoroughly clean first,for dirt will weaken the weld.Moreover,the heating of iron or steel to a high temperature cause oxidation,and a film of oxide is added to the heated surfaces.For this reason,flux is applied to the heated metal.At welding heat,flux melts and the oxide particles are dissolved in it together with any other impurities which may be present.The metal surfaces are pressed together,and the flux is squeezed out from the center of the weld.A number of different types of weld may be used,but for fairly thick bars of metals,a vee-shaped belt should be normally employed.It is rather stronger than ordinary butt weld. The simplest way of welding two pieces of metal together is....
MCQ->1000 Kg of liquid at 30°C in a well stirred vessel has to be heated to 120°C, using immersed coils carrying condensing steam at 150°C. The area of the steam coils is 1.2 m2 and the overall heat transfer co-efficient to the liquid is 1500 W/m2.°C. Assuming negligible heat loss to the surrounding and specific heat capacity of the liquid to be 4 kJ/kg.°C, the time taken for the liquid to reach desired temperature will be....
MCQ->The following heat engine produces power of 100000 kW. The heat engine operates between 800 K and 300 K. It has a thermal efficiency equal to 50% of that of the Carnot engine for the same temperature. The rate at which heat is absorbed from the hot reservoir is....
Terms And Service:We do not guarantee the accuracy of available data ..We Provide Information On Public Data.. Please consult an expert before using this data for commercial or personal use | Powered By:Omega Web Solutions
© 2002-2017 Omega Education PVT LTD...Privacy | Terms And Conditions
Question ANSWER With Solution