Toggle navigation
Home
KPSC Previous Question Papers
Article Category
kerala psc
upsc
General
Popular Pages
Multiple Choice Question in engineering-mechanics-kinetics-of-a-particle-impulse-and-momentum
Multiple Choice Question in database-database-redesign
Question Answer in malayalam-kerala-psc-questions
Multiple Choice Question in malayalam-kerala-psc-questions
Multiple Choice Question in current-affairs-2017-03-05
Question Answer in kerala-psc-questions-in-malayalam
Multiple Choice Question in kerala-psc-questions-in-malayalam
Multiple Choice Question in electronics-and-communication-engineering-electronic-devices-and-circuits
Multiple Choice Question in database-sql-for-database-construction-and-application-processing
Question Answer in Antonyms
Multiple Choice Question in 035/2016
Question Answer in KERALA PSC
Multiple Choice Question in KERALA PSC
Question Answer Bank
Multiple Choice Question Bank
Question Answer Category
Multiple Choice Question Category
Home
->
Multiple Choice Questions
Question Set
mechanical engineering automobile engineering
1. What type of bearing is used for main bearings and connecting rod bearings ?
(A): Ballbearings
(B): Needle roller bearing
(C): Plain bearings
(D): Taper roller bearing
Previous Question
Show Answer
Next Question
Add Tags
Report Error
Show Marks
Ask Your Doubts Here
Type in
(Press Ctrl+g to toggle between English and the chosen language)
Post reply
Comments
Show Similar Question And Answers
QA->Connecting rod is attached to the piston by:....
QA->_________is connecting the carriage with Main Spring.....
QA->In a secret way of writing COME AT ONCE FATHER VERY ILL is written as XLNV ZG LMXY UYGSVI EVIB ROO.Bearing this in mind pick up the code from the answer choices for the word given below: FIT AND WELL....
QA->What is the connecting link between Annelida and Arthropoda?....
QA->Which Strait connecting Arabian Sea and the Bay of Bengal?....
MCQ->What type of bearing is used for main bearings and connecting rod bearings ?....
MCQ->The cylindrical cam C is held fixed while the rod AB and bearings E and F rotate about the vertical axis of the cam at a constant rate of = 4 rad/s. If the rod is free to slide through the bearings, determine the magnitudes of the velocity and acceleration of the guide D on the rod as a function of . The guide follows the groove in the cam, and the groove is defined by the equations r = 0.25 ft and z = (0.25 cos ) ft.....
MCQ->A rotor which is balanced statically but not dynamically is supported on two bearings L apart and at high speed of the rotor, reaction on the left bearing is R. The right side of the bearing is shifted to a new position 2 L apart from the left bearing. At the same rotor speed, dynamic reaction on the left bearing in the new arrangement will....
MCQ->In the below figure, PC is the connecting rod and OC is the crank making an angle θ with the line of stroke PO and rotates with uniform angular velocity at ω rad/s. The Klien's acceleration diagram for determining the acceleration of the piston P is shown by quadrilateral C Q NO, the acceleration of the piston is zero when the crank OC and connecting rod PC are at right angles to each other. ....
MCQ->A 600 mm long and 50 mm diameter rod of steel (E = 200 GPa, α = 12 x 10-6/°C) is attached at the ends to unyielding supports. When the temperature is 30°C there is no stress in the rod. After the temperature of the rod drops to - 20°C, the axial stress in the rod will be....
×
×
Type The Issue
×
Your Marks
Terms And Service:We do not guarantee the accuracy of available data ..We Provide Information On Public Data.. Please consult an expert before using this data for commercial or personal use | Powered By:Omega Web Solutions
© 2002-2017 Omega Education PVT LTD...
Privacy
|
Terms And Conditions
Question ANSWER With Solution