Toggle navigation
Home
KPSC Previous Question Papers
Article Category
kerala psc
upsc
General
Popular Pages
Multiple Choice Question in aptitude-area
Multiple Choice Question in non-verbal-reasoning-grouping-of-images
Multiple Choice Question in aptitude-compound-interest
Multiple Choice Question in engineering-mechanics-kinetics-of-a-particle-impulse-and-momentum
Multiple Choice Question in 035/2016
Multiple Choice Question in electronic-devices-bipolar-junction-transistors
Question Answer in
Multiple Choice Question in database-database-redesign
Question Answer in malayalam-kerala-psc-questions
Multiple Choice Question in malayalam-kerala-psc-questions
Multiple Choice Question in current-affairs-2017-03-05
Question Answer Bank
Multiple Choice Question Bank
Question Answer Category
Multiple Choice Question Category
Home
->
Multiple Choice Questions
Question Set
mechanical engineering engineering materials
1. Which of the following metal shrinks most from molten state to solid state?
(A): Admirality metal
(B): Brass
(C): Cast iron
(D): Cast steel
Previous Question
Show Answer
Next Question
Add Tags
Report Error
Show Marks
Ask Your Doubts Here
Type in
(Press Ctrl+g to toggle between English and the chosen language)
Post reply
Comments
Show Similar Question And Answers
QA->The oldest rocks in the earth's crust were once molten; and came from deep inside the earth. The molten rock; called magma; spewed out in volcanic eruptions during the earth;s early life and solidified into hard rock's called?....
QA->A white solid’A’on heating gives off a gas which turns lime water milky.The residue is yellow when hot but turns white on cooling .The solid A is:....
QA->If a non-metal is added to the interstitial sites of a metal, then the metal becomes?....
QA->The process by which a substance is changed from solid state to liquid state is called?....
QA->The fixed temperature at which a substance is changed from solid state to liquid state is called?....
MCQ->Which of the following metal shrinks most from molten state to solid state?....
MCQ->The simplest method of welding two pieces of metal together is known as pressure welding.The ends of a metal are heated to a white heat-for iron,the welding temperature should be about 1300C-in a flame.At this temperature the metal becomes plastic.The ends are pressed or hammered together,and the joint is smoothed off.Care must be taken to ensure that surfaces are thoroughly clean first,for dirt will weaken the weld.Moreover,the heating of iron or steel to a high temperature cause oxidation,and a film of oxide is added to the heated surfaces.For this reason,flux is applied to the heated metal.At welding heat,flux melts and the oxide particles are dissolved in it together with any other impurities which may be present.The metal surfaces are pressed together,and the flux is squeezed out from the center of the weld.A number of different types of weld may be used,but for fairly thick bars of metals,a vee-shaped belt should be normally employed.It is rather stronger than ordinary butt weld. The simplest way of welding two pieces of metal together is....
MCQ->Consider the following statements : In solid waste management 1. density separation of solid wastes can be accomplished by air classifiers. 2. iron recovery from solid wastes can be done by magnetic separators. 3. aluminium separation from solid wastes can be accomplished by eddy current separators. Which of the statements given above are correct ?....
MCQ->200 kg of solids (on dry basis) is subjected to a drying process for a period of 5000 seconds. The drying occurs in the constant rate period with the drying rate as, Nc = 0.5 x 10-3 kg/m2.s. The initial moisture content of the solid is 0.2 kg moisture/kg dry solid. The interfacial area available for drying is 4 m2/1000 kg of dry solid. The moisture content at the end of the drying period is (in kg moisture/kg dry solid)....
MCQ->Pick out thể one word for - a secret arrangement....
×
×
Type The Issue
×
Your Marks
Terms And Service:We do not guarantee the accuracy of available data ..We Provide Information On Public Data.. Please consult an expert before using this data for commercial or personal use | Powered By:Omega Web Solutions
© 2002-2017 Omega Education PVT LTD...
Privacy
|
Terms And Conditions
Question ANSWER With Solution