1. You have your laptop directly connected into a router's Ethernet port. Which of the following are among the requirements for the copy flash tftp command to be successful? TFTP server software must be running on the router. TFTP server software must be running on your laptop. The Ethernet cable connecting the laptop directly into the router's Ethernet port must be a straight-through cable. The laptop must be on the same subnet as the router's Ethernet interface. The copy flash tftp command must be supplied the IP address of the laptop.





Ask Your Doubts Here

Type in
(Press Ctrl+g to toggle between English and the chosen language)

Comments

  • By: guest on 02 Jun 2017 01.56 am
    Before you back up an IOS image to a laptop directly connected to a router's Ethernet port, make sure the TFTP server software is running on your laptop, that the Ethernet cable is a "crossover," and that the laptop is in the same subnet as the router's Ethernet port, and then you can use the copy flash tftp command from your laptop.
Show Similar Question And Answers
QA->Have you _____ money on you ?....
QA->Which consortium serves as an interface to the Indian software industry & Indian BPO industry?....
QA->A line that connects points on a map that have the same temperature is ______?....
QA->A _____ is a computer attached to the internet that runs a special web server software and can send web pages out to the other computer over the internet.....
QA->Which places are connected by the train of Azad Hind Express?....
MCQ->You have your laptop directly connected into a router's Ethernet port. Which of the following are among the requirements for the copy flash tftp command to be successful? TFTP server software must be running on the router. TFTP server software must be running on your laptop. The Ethernet cable connecting the laptop directly into the router's Ethernet port must be a straight-through cable. The laptop must be on the same subnet as the router's Ethernet interface. The copy flash tftp command must be supplied the IP address of the laptop.....
MCQ->A network administrator is connecting hosts A and B directly through their Ethernet interfaces, as shown in the illustration. Ping attempts between the hosts are unsuccessful. What can be done to provide connectivity between the hosts? A crossover cable should be used in place of the straight-through cable. A rollover cable should be used in place of the straight-through cable. The subnet masks should be set to 255.255.255.192. A default gateway needs to be set on each host. The subnet masks should be set to 255.255.255.0.....
MCQ->You are the administrator of the Windows 2000 Server network shown in the exhibit. Users in the Research group and the Executive group have permission to access the Internet through a Windows 2000 Server computer running Microsoft Proxy Server. These users must enter their proxy server user names and passwords to connect to the proxy server, to the Internet, and to your local intranet server. The users who do not access the Internet do not have user accounts on the proxy server and, therefore, cannot connect to the intranet server. You want all users to be able to connect to the intranet server without entering a separate user name and password. What should you do?....
MCQ->You install the Routing and Remote Access service on a Windows 2000 Server computer in your network. Your network is not directly connected to the Internet and uses the private IP address range 192.168.0.0. When you use Routing and Remote Access to dial in to the server, your computer connects successfully, but you are unable to access any resources. When you try to piiig servers by using their IP addresses, you receive the following message: "Request timed out." When you run the ipconfig command, it shows that your dial-up connection has been given the IP address 169.254.75.182. What should you do to resolve the problem?....
MCQ->You are setting up a network in a school. You need to network 5 computers for the file and printer sharing. You want to use some donated cable and Ethernet adapters. You identify the donated adapters as ARCnet coaxial network adapters and 10Base2 Ethernet network adapters. You install an Ethernet adapter in each of the 5 computers and connect the donated cable. The computers are NOT able to maintain reliable communication. You suspect that you are NOT using the correct type of coaxial cable. Which type of coaxial cable should you be using?....
Terms And Service:We do not guarantee the accuracy of available data ..We Provide Information On Public Data.. Please consult an expert before using this data for commercial or personal use | Powered By:Omega Web Solutions
© 2002-2017 Omega Education PVT LTD...Privacy | Terms And Conditions