Toggle navigation
Home
KPSC Previous Question Papers
Article Category
kerala psc
upsc
General
Popular Pages
Multiple Choice Question in non-verbal-reasoning-grouping-of-images
Multiple Choice Question in engineering-mechanics-kinetics-of-a-particle-impulse-and-momentum
Multiple Choice Question in database-database-redesign
Question Answer in malayalam-kerala-psc-questions
Multiple Choice Question in malayalam-kerala-psc-questions
Multiple Choice Question in current-affairs-2017-03-05
Multiple Choice Question in 035/2016
Multiple Choice Question in malayalam_lang
Question Answer in kerala-psc-questions-in-malayalam
Multiple Choice Question in kerala-psc-questions-in-malayalam
Multiple Choice Question in c-programming-const
Question Answer in KERALA PSC
Multiple Choice Question in KERALA PSC
Question Answer Bank
Multiple Choice Question Bank
Question Answer Category
Multiple Choice Question Category
Home
->
Multiple Choice Questions
Question Set
chemical engineering heat transfer
1. Which of the following is the most controlling factor for the rate of bubble detachment from the hot solid surface ?
(A): Hot surface temperature
(B): Interfacial tension
(C): Liquid density
(D): Liquid viscosity
Previous Question
Show Answer
Next Question
Add Tags
Report Error
Show Marks
Ask Your Doubts Here
Type in
(Press Ctrl+g to toggle between English and the chosen language)
Post reply
Comments
Show Similar Question And Answers
QA->A white solid’A’on heating gives off a gas which turns lime water milky.The residue is yellow when hot but turns white on cooling .The solid A is:....
QA->A liquid will not wet the surface of solid if the angle of contact is which angle?....
QA->If the absolute temperature of a perfectly black body id doubled, then its rate of radiation increases by a factor of?....
QA->Surface tension of hot water is less than that of?....
QA->The rate of cooling of hot water will be faster than the?....
MCQ->Which of the following is the most controlling factor for the rate of bubble detachment from the hot solid surface ?....
MCQ->If the staff intercept on a staff located at 100 m from the level for five division deviation of the bubble is 0.050 m and if the length of one division of the bubble is 2 mm, then the radius of curvature of the bubble is 0.050 m and if the length of one division of the bubble is 2 mm, then the radius of curvature of the bubble tube is....
MCQ->200 kg of solids (on dry basis) is subjected to a drying process for a period of 5000 seconds. The drying occurs in the constant rate period with the drying rate as, Nc = 0.5 x 10-3 kg/m2.s. The initial moisture content of the solid is 0.2 kg moisture/kg dry solid. The interfacial area available for drying is 4 m2/1000 kg of dry solid. The moisture content at the end of the drying period is (in kg moisture/kg dry solid)....
MCQ->A solid is being dried in the linear drying rate regime from moisture content Xo to XF. The drying rate is zero at X = 0 and the critical moisture content is the same as the initial moisture Xo. The drying time for M = (Ls/ARc) is (where, L = total mass of dry solid, A = total surface area for drying Rc = Constant maximum drying rate per unit area X = moisture content (in mass of water/mass of dry solids))....
MCQ->The following statements relate to the pressure exerted by a fluid on a Submerged curved surface : 1. The vertical component of hydrostatic force acting on a submerged curved surface acts through the centre of volume of the fluid directly above the submerged area. 2. The horizontal component of the force acting on a curved surface is the hydrostatic force acting on the vertical projection of the curved surface. 3. The resultant force on a curved surface acts on the bottom of th6 curved surface. Of these statements :....
×
×
Type The Issue
×
Your Marks
Terms And Service:We do not guarantee the accuracy of available data ..We Provide Information On Public Data.. Please consult an expert before using this data for commercial or personal use | Powered By:Omega Web Solutions
© 2002-2017 Omega Education PVT LTD...
Privacy
|
Terms And Conditions
Question ANSWER With Solution