Question Set

1. The crane provides a long-reach capacity by using the telescopic boom segment DE. The entire boom is supported by a pin at A and by the telescopic hydraulic cylinder BC, which can be considered as a two-force member. The rated load capacity of the crane is measured by a maximum force developed in the hydraulic cylinder. If this maximum force is developed when the boom supports a mass m = 6 Mg and its length is l = 40 and = 60°, determine the greatest mass that can be supported when the boom length is extended to l = 50 m and = 45°. Neglect the weight of the boom and the size of the pulley at E. Assume the crane does not overturn. Note: when = 60° BC is vertical; however, when = 45° this is not the case.





Ask Your Doubts Here

Type in
(Press Ctrl+g to toggle between English and the chosen language)

Comments

Show Similar Question And Answers
QA->In Kiran’s opinion, his weight is greater than 65 kg but less than 72 kg. His brother does not agree with Kiran and he thinks that Kiran’s weight is greater than 60 kg but less than 70 kg. His mother’s view is that his weight cannot be greater than 68 kg. If all are them are correct in their estimation, what is the average of different probable weights of Kiran?....
QA->The weight of a dog is 8kg more than of of its weight. The weight of the dog is :....
QA->The average weight of A, B and C is 45 kg. If the average weight of A and B be 40 kg and that of B and C be 43 kg, what is the weight of B?....
QA->If a solid does not regain its original shape and size, when the deforming force is removed, it is called?....
QA->The average weight of 10 men is decreased by 3 kg when one of them whose weight is 80 kg is replaced by a new person. The weight of the new person is—....
MCQ->The crane provides a long-reach capacity by using the telescopic boom segment DE. The entire boom is supported by a pin at A and by the telescopic hydraulic cylinder BC, which can be considered as a two-force member. The rated load capacity of the crane is measured by a maximum force developed in the hydraulic cylinder. If this maximum force is developed when the boom supports a mass m = 6 Mg and its length is l = 40 and = 60°, determine the greatest mass that can be supported when the boom length is extended to l = 50 m and = 45°. Neglect the weight of the boom and the size of the pulley at E. Assume the crane does not overturn. Note: when = 60° BC is vertical; however, when = 45° this is not the case.....
MCQ->The flying boom B is used with a crane to position construction materials in coves and underhangs. The horizontal "balance" of the boom is controlled by a 250-kg block D, which has a center of gravity at G and moves by internal sensing devices along the bottom flange F of the beam. Determine the position x of the block when the boom is used to lift the stone S, which has a mass of 60 kg. The boom is uniform and has a mass of 80 kg.....
MCQ->Consider the following statements associated with the laws of weights in the theory of erros : 1. If an equation is multiplied by its own weight, then the weight of the resulting equation is equal to the reciprocal of the weight of the equation. 2. The weight of the algebraic sum of two or more quantities is equal to the reciprocal of the sum of the individual weights. 3. If the quantity of a given weight is multiplied by a factor, then the weight of the result is obtained by dividing its given weight by the square root of that factor. 4. If the quantity of a given weight is divided by a factor, then the weight of the result is obtained by multiplying its given weight by the square of that factor. Of these statements :....
MCQ->The oil rig is supported on the trailer by the pin or axle at A and the frame at B. If the rig has a weight of 115,000 lb and the center of gravity at G, determine the force F that must de developed along the hydraulic cylinder CD in order to start lifting the rig (slowly) off B toward the vertical. Also compute the horizontal and vertical components of reaction at the pin A.....
MCQ->What will be the output of the C#.NET code snippet given below? char ch = Convert.ToChar ('a' | 'b' | 'c'); switch (ch) { case 'A': case 'a': Console.WriteLine ("case A | case a"); break; case 'B': case 'b': Console.WriteLine ("case B | case b"); break; case 'C': case 'c': case 'D': case 'd': Console.WriteLine ("case D | case d"); break; }....
Terms And Service:We do not guarantee the accuracy of available data ..We Provide Information On Public Data.. Please consult an expert before using this data for commercial or personal use | Powered By:Omega Web Solutions
© 2002-2017 Omega Education PVT LTD...Privacy | Terms And Conditions
Question ANSWER With Solution