<<= Back Next =>>
You Are On Multi Choice Question Bank SET 1484

74201. When the shear force diagram is a parabolic curve between two points, it indicates that there is a

74202. The efficiency of a riveted joint is the ratio of the strength of the joint to the strength of the solid plate.

74203. You ......... replied rudely.?

74204. The slenderness ratio is the ratio of

74205. When two shafts of same length, one of which is hollow, transmit equal torques and have equal maximum stress, then they should have equal

74206. For a beam, as shown in the below figure, the maximum deflection lies at

74207. According to Euler's column theory, the crippling load for a column of length (l) fixed at both ends is __________ the crippling load for a similar column hinged at both ends.

74208. The shear force and bending moment are zero at the free end of a cantilever beam, if it carries a

74209. A rod is enclosed centrally in a tube and the assembly is tightened by rigid washers. If the assembly is subjected to a compressive load, then

74210. A bar of length L metres extends by l mm under a tensile force of P. The strain produced in the bar is

74211. A shaft revolving at ω rad / s transmits torque (T) in N-m. The power developed is

74212. The unit of modulus of elasticity is same as those of

74213. When a bar of length l, width b and thickness t is subjected to a pull of P, its

74214. A column with maximum equivalent length has

74215. A column of length (l) with both ends fixed may be considered as equivalent to a column of length __________ with both ends hinged.

74216. The product of the tangential force acting on the shaft and its distance from the axis of the shaft (i.e. radius of shaft) is known as

74217. When a body is subjected to a direct tensile stress (σ) in one plane, the maximum shear stress is __________ the maximum normal stress.

74218. A simply supported beam 'A' of length l, breadth b and depth d carries a central load W. Another beam 'B' of the same dimensions carries a central load equal to 2 W. The deflection of beam 'B' will be __________ as that of beam 'A'.

74219. Nehru supported the policy of ----- to deal with the tribal population in India?

74220. In the below figure, the point E represents the maximum stress.

74221. The ratio of the largest load in a test to the original cross-sectional area of the test piece is called

74222. According to Euler's column theory, the crippling load of a column is given by p = π2 EI/Cl2. In the Euler's formula, the value of C for a column with one end fixed and the other end free, is

74223. Strain is equal to (where l = Original length, and δl = Change in length)

74224. The total strain energy stored in a body is termed as

74225. Modulus of resilience is the proof resilience per unit volume of a material.

74226. In order to avoid sliding of masonry dam, the force of friction between the dam and soil should be at least __________ the total water pressure per metre length.

74227. In a beam subjected to pure bending, the intensity of stress in any fibre is __________ the distance of the fibre from the neutral axis.

74228. Who invented a method of reading for the blind?

74229. If the modulus of elasticity of a material is twice its modulus of rigidity, then the Poisson's ratio of the material is equal to zero.

74230. A beam of T-section is subjected to a shear force of F. The maximum shear force will occur at the

74231. When there is no increase or decrease in shear force between two points, it indicates that there is no change in the bending moment between these points.

74232. Two bars of different materials and same size are subjected to the same tensile force. If the bars have unit elongation in the ratio of 2:5, then the ratio of modulus of elasticity of the two materials will be

74233. A beam of uniform strength may be obtained by

74234. The springs in brakes and clutches are used to

74235. The maximum deflection of a fixed beam carrying a central point load lies at

74236. The first monarch of Magadha kingdom in the sixth century B.C. was?

74237. Parallel fillet welds are designed for bending strength.

74238. The design of thin cylindrical shells is based on

74239. ‘Controversially Yours’ is the autobiography of?

74240. The pull required to crush the rivet per pitch length is

74241. The first war of independence was fought in the year .........?

74242. The deformation of the bar per unit length in the direction of the force is known as

74243. Which planet has rings around it?

74244. Who is known as plastic girl?

74245. In watches, the spring is used to absorb shocks and vibrations.

74246. All of the following kings of the Haryanka line in the sixth and fifth centruies B.c. were parricides, except?

74247. The volumetric strain is the ratio of the

74248. Codes of conduct of the Vedic society are laid down in which of the following specifically?

74249. The breaking stress is __________ the ultimate stress.

74250. A bolt is made to pass through a tube and both of them are tightly fitted with the help of washers and nuts. If the nut is tightened, then

<<= Back Next =>>
Terms And Service:We do not guarantee the accuracy of available data ..We Provide Information On Public Data.. Please consult an expert before using this data for commercial or personal use | Powered By:Omega Web Solutions
© 2002-2017 Omega Education PVT LTD...Privacy | Terms And Conditions
Question ANSWER With Solution