<<= Back Next =>>
You Are On Multi Choice Question Bank SET 1585

79251. This is the range of digital or hard copy documents that specify the physical function requirements for a product:





79252. An architect often relies on a ________ to complete the set of technical drawings used in the design of an office building.





79253. Enhancing product development is considered aesthetic design.



79254. Drawings and specifications typically do not control details of maintenance.



79255. PDM is the acronym for:





79256. Students can complete an associate's degree in drafting which normally takes about ________ years to complete.





79257. Technical drawings typically serve one of three purposes:





79258. Traditionally, design and manufacturing activities have taken place in sequential order.



79259. The organized and orderly approach to solving problems is known as the:





79260. In perspective drawings this is placed between the observer and the object:





79261. (solve as per the direction given above)





79262. Which agency was secured Krupasakaya Award of UNESCO?





79263. The leader of Yachana Yathra





79264. Representation of Travancore in the constituent assembly





79265. In which year Poor Home Society was established?





79266. The editor of the magazine ‘Murali’





79267. DEAR





79268. The founder of ‘Society for the Promotion of Education of Women’





79269. In which year Deena Bandhu was started?





79270. The capital of Andhra Pradesh





79271. His father won't be able to leave for Varnasi until they have arrived.





79272. Some boys are sitting in three rows all facing North such that A is in the middle row. P is just to the right of A but in the same row. Q is just behind of P while R is in the North of A. In which direction of R is Q?





79273. P started from his house towards west. After walking a distance of 25 m. He turned to the right and walked 10 m. He then again turned to the right and walked 15 m. After this he is to turn right at 135o and to cover 30 m. In which direction should he go?





79274. One morning after sunrise, Vimal started to walk. During this walking he met Stephen who was coming from opposite direction. Vimal watch that the shadow of Stephen to the right of him (Vimal). To Which direction Vimal was facing?





79275. Rohit walked 25 m towards south. Then he turned to his left and walked 20 m. He then turned to his left and walked 25 m. He again turned to his right and walked 15 m. At what distance is he from the starting point and in which direction?





79276. Which tree is just opposite to raspberry tree?





79277. Village Q is to the North of the village P. The village R is in the East of Village Q. The village S is to the left of the village P. In which direction is the village S with respect to village R?





79278. One morning Udai and Vishal were talking to each other face to face at a crossing. If Vishal's shadow was exactly to the left of Udai, which direction was Udai facing?





79279. If South-East becomes North, North-East becomes West and so on. What will West become?





79280. The length and breadth of a room are 8 m and 6 m respectively. A cat runs along all the four walls and finally along a diagonal order to catch a rat. How much total distance is covered by the cat?





79281. A child went 90 m in the East to look for his father, then he turned right and went 20 m. After this he turned right and after going 30 m he reached to his uncle's house. His father was not there. From there he went 100 m to his north and met his father. How far did he meet his father from the starting point?





79282. Which one of the following is always in 'Sentiment'?





79283. This is a rounded exterior blend between surfaces:





79284. If a plane intersects a contoured surface, no line is drawn to represent the edge.



79285. Right-hand and left-hand parts are mirror images and are made to be interchangeable.



79286. A keyway is a small groove cut around the diameter of a cylinder, often where it changes diameter.



79287. A plane surface cannot intersect or be tangent to a contoured surface.



79288. Small curves called runouts are used to represent fillets that connect with plane surfaces tangent to cylinders.



79289. A fillet is a rounded exterior blend between surfaces.



79290. Knurl is a pattern form on a surface to provide for better gripping or more surface area for attachment.



79291. A counterbore is a cylindrical recess around a hole, usually to receive a bolt head or nut.



79292. Simplified conventional representations that deviate from true orthographic projection may be used to enhance economy and clarity in a drawing.



79293. A lug is a flattened collar or rim around a cylindrical part to allow for attachment.



79294. When a curved surface intersects a plane surface, an edge is formed.



79295. It is not always possible to show all of the drawing views in alignment on a sheet.



79296. A boss is a short raised protrusion above the surface of a part.



79297. This is a conical-shaped recess around a hole, often used to receive a tapered screw head:





79298. This is an angled surface used on cylinders to make them easier to handle:





79299. These are used to attach parts to a cylinder so they won't turn on it:





79300. This is a flat or rounded tab protruding from a surface, usually to provide a method for attachment:





<<= Back Next =>>
Terms And Service:We do not guarantee the accuracy of available data ..We Provide Information On Public Data.. Please consult an expert before using this data for commercial or personal use | Powered By:Omega Web Solutions
© 2002-2017 Omega Education PVT LTD...Privacy | Terms And Conditions
Question ANSWER With Solution