73151. The pressure angle for involute gears depends upon the size of teeth.
73152. When a belt drive is transmitting maximum power,
73153. Gears are casted by
73154. Name the book written by Rabindra Nath Tagore?
73155. When a cylinder is subjected to a very high internal fluid pressure, the thin cylinder should be used.
73156. In a full journal bearing, the angle of contact of the bearing with the journal is
73157. In a flat belt drive, if the slip between the driver and belt is 1 %, between the belt and follower is 3% and driver and follower pulley diameters are equal, then velocity ratio of the drive will be
73158. A cotter joint is used to connect two __________ rods.
73159. A bolt has
73160. The material commonly used for machine tool bodies is
73161. The power transmitted by a belt drive is maximum when the maximum tension in the belt is __________ the centrifugal tension.
73162. The largest diameter of an external or internal screw thread is known as
73163. The gears are termed as medium velocity gears, if their peripheral velocity is
73164. The product of the diametral pitch and circular pitch is equal to
73165. If T1 and T2 are the tensions on the tight and slack sides of the belt respectively, and Tc is the centrifugal tension, then initial tension in the belt is equal to
73166. The smallest diameter of an external or internal screw thread is known as
73167. The process which improves the machinability of steels, but lowers the hardness and tensile strength is
73168. Parasuram Express runs between Thiruvananthapuram and .........?
73169. A screw is said to be a self locking screw, if its efficiency is
73170. An aluminium member is designed on the basis of
73171. A plate with a circular hole in the centre is subjected to a pull of P. The maximum stress induced at the edge of the hole is three times of the nominal stress.
73172. The cold working of metals is carried out __________ the recrystallisation temperature.
73173. The groove angle of the pulley for rope drive is usually
73174. The ratio of pitch circle diameter in millimetres to the number of teeth, is called
73175. According to Indian standard specifications, 100 H6/g5 means that
73176. Rankine Gordon formula for buckling is valid for
73177. The angle of twist of shaft is
73178. A long helical spring having a spring stiffness of 12 kN/m and number of turns 20, breaks into two parts with number of turns 10 each in both the parts. If the two parts are connected in series, then the softness of the resultant spring will be
73179. Mary declared that the book was not ..........?
73180. The coefficient of friction between the belt and pulley depends upon the
73181. The allowable static stress for steel gears is approximately __________ of the ultimate tensile stress.
73182. The pitch diameter is the __________ diameter of an external or internal screw thread.
73183. When a hole of diameter 'd' is punched in a metal of thickness 't', then the force required to punch a hole is equal to (where τu = Ultimate shear strength of the material of the plate)
73184. When percentage of carbon in steel is increased, the ductility of steel decreases.
73185. The shock absorbing capacity of a bolt may be increased by
73186. A lap joint is always in single shear.
73187. If b denotes the face width and L denotes the cone distance for a bevel gear, then the bevel factor is written as
73188. The design calculations for members subject to fluctuating loads with the same factor of safety, yield the most conservative estimates when using
73189. Fill up the blanks with suitable words: You must stop ......... .?
73190. The taper on cotter and slot is made on both the sides.
73191. Teflon is used for bearings because of
73192. In designing a flange coupling, the pitch circle diameter of bolts is taken as (where d = Diameter of the shaft)
73193. The acme threads are usually found on
73194. The radial distance from the __________ to the clearance circle is called working depth.
73195. The efficiency of a square threaded screw is maximum if the helix angle is equal to (where φ = Angle of friction)
73196. In designing thick cylinders, the equation used is
73197. In the first free multi party general election held in the history general election held in the history of South Africa, who was elected as the President?
73198. Two shafts A and B are made of the same material. The diameter of shaft A is twice as that of shaft B. The power transmitted by the shaft A will be __________ of shaft B.
73199. A parallel sunk key, made of steel, is equally strong in shearing and crushing.
73200. In designing a key, it is assumed that the distribution of forces along the length of key